MitoPedia: O2k hardware

From Bioblast


                  


O2k-Open Support

MitoPedia: O2k hardware



Template NextGen-O2k.jpg


MitoPedia O2k and high-resolution respirometry: O2k-Open Support 



MitoPedia




MitoPedia: O2k hardware is a component of O2k-Open Support.
It lists hardware-related topics and the O2k-Modules and main components of the O2k system.


Questions.jpg


Click to expand or collaps


See also
» Complete list of O2k components O2k-Products


TermAbbreviationDescription
Barometric pressurepb [Pa]Barometric pressure, pb, is an important variable measured for calibration of oxygen sensors in solutions equilibrated with air. The atm-standard pressure (1 atm = 760 mmHg = 101.325 kPa) has been replaced by the SI standard pressure of 100 kPa. The partial pressure of oxygen, pO2, in air is a function of barometric pressure, which changes with altitude and locally with weather conditions. The partial oxygen pressure declines by 12 % to 14 % per 1,000 m up to 6,000 m altitude, and by 15 % to 17 % per 1,000 m between 6,000 and 9,000 m altitude. The O2k-Barometric Pressure Transducer is built into the Oroboros O2k as a basis for accurate air calibrations in high-resolution respirometry. For highest-level accuracy of calculation of oxygen pressure, it is recommended to compare at regular intervals the barometric pressure recording provided by the O2k with a calibrated barometric pressure recording at an identical time point and identical altitude. The concept of gas pressure or barometric pressure can be related to the generalized concept of isomorphic pressure.
Block temperatureThe block temperature of the Oroboros O2k is the continuously measured temperature of the copper block, housing the two glass chambers of the O2k. The block temperature is recorded by DatLab as one of the O2k system channels.
ChannelF7» See O2k signals and output
Cover-Slip\black
Cover-Slip black.JPG
A Cover-Slip should be placed on top of the O2k-Stopper to minimize contamination and evaporation of liquid extruding from the capillary of the stopper. The Cover-Slips do not exert any direct effect on oxygen backdiffusion into the O2k-chamber. Use the the Cover-Slip\black to avoid light penetration and disturbance of fluorescence signals and generally for optical measurements in the O2k.
DatLab
DatLab
DatLab is the O2k-Software for Data Acquisition & Analysis, specifically developed for high-resolution respirometry with the O2k.

The newest DatLab version is DatLab 8, included in the O2k-Packages. NextGen-O2k and O2k-Series J* and higher come with DatLab 8 installed on the integrated PC (Linux). DatLab 8 is required for the NextGen-O2k. DatLab 8.2 is compatible with O2k-Series (E and higher).

The DatLab software is designed for 64-bit versions of Windows operating systems and does not run on MAC devices.

The minimum computer requirements are Intel-Core-2 or equivalent CPU, 2GB RAM and Windows XP (64-bit version). However, we recommend Intel i5 or equivalent CPU, 4GB RAM, Windows 10 (64-bit version) and SSD. For the proper display of DatLab on your computer, please make sure the “Language settings” are set to English.

*Optionally available without integrated PC.
Electrolyte\Reference-Electrode
Electrolyte Reference-Electrode.jpg
Electrolyte\Reference-Electrode for Reference-Electrode\2.4 mm
Filter Set AmR
Filter Set AmR.JPG
Filter Set AmR: Set of filters for the determination of H2O2 production with Amplex UltraRed. These filters should be used together with Fluorescence-Sensor Green. The filter set consists of 6 LED filters (round) and 6 photodiode filters (rectangular).
Filter Set MgG / CaG
Filter Set MgG CaG.JPG
Filter set MgG / CaG: Set of filters for the determination of concentraions of Mg2+ or Ca2+ with the fluorophores Magnesium green and Calcium green, respectively. These filters should be used together with Fluorescence-Sensor Blue or Smart Fluo-Sensor Blue. The filter set consists of 6 LED filters (round) and 6 photodiode filters (rectangular).
Filter Set Saf
Filter Set Saf.JPG
Filter set Saf: Set of filters for the (qualitative) determination of mitochondrial membrane potential with Safranin. These filters should be used together with Fluorescence-Sensor Blue or Smart Fluo-Sensor Blue. The filter set consists of 6 LED filters (round) and 6 photodiode filters (rectangular).
Filter-Cap
Filter-Cap.JPG
Filter-Cap: O2k-Fluo LED2-Module (O2k-Series D to G) sensors (Fluorescence-Sensor Green and Fluorescence-Sensor Blue) and O2k-FluoRespirometer (O2k-Series H to I) sensors (Smart Fluo-Sensor Green and Smart Fluo-Sensor Blue) are equipped with a removable Filter-Cap for exchange of optical filters for the optical pathways from the LED to the sample and from the sample to the photodiode.
Fluorescence-Control Unit
Fluorescence-Control Unit lettered.jpg
Fluorescence-Control Unit with O2k-Front Fixation, Current-Control (O2k-Chamber A and B) for regulation of light intensity of the LED in the fluorescence sensors. This item is a standard component of the O2k-Fluorescence LED2-Module.
Fluorescence-Sensor Blue
Fluorescence-Sensor Blue.JPG
Fluorescence-Sensor Blue: excitation LED 465 nm (dominant wavelength), photodiode, Filter-Cap equipped with Filter Set Saf for measurement of mitochondrial membrane potential with Safranin when delivered. The filter set Filter Set MgG / CaG for Magnesium green® / Calcium green® measurements is included.
Fluorescence-Sensor Green
Fluorescence-Sensor Green.JPG
Fluorescence-Sensor Green: excitation LED 525 nm (dominant wavelength), photodiode, Filter-Cap equipped with Filter Set AmR for Amplex UltraRed measurements when delivered.
FluorometryFluorometry (or fluorimetry) is the general term given to the method of measuring the fluorescent emission of a substance following excitation by light at a shorter wavelength.
Forceps for membrane application
Forcep for membrane application.jpg
Forceps for membrane application: for OroboPOS and ISE membrane application; do not use for tissue preparation.
Forceps\stainless Steel\angular Tip\fine
Forcep for tissue preparation angular tip.jpg
Forceps\stainless Steel\angular Tip\fine: for tissue preparation, stainless steel. Two pairs are used particularly for muscle fiber separation.
Forceps\stainless Steel\rounded Tip\sharp
Forcep for tissue preparation rounded tip.jpg
Forceps\stainless Steel\rounded Tip\sharp: for tissue preparation, stainless steel, antimagnetic. One pair is recommended for placing the tissue sample onto the microbalance and for handling in combination with Forceps\stainless Steel\straight Tip\sharp.
Forceps\stainless Steel\straight Tip\sharp
Forcep for tissue preparation straight tip.jpg
Forceps\stainless Steel\straight Tip\sharp: for tissue preparation, stainless steel, antimagnetic. One pair is recommended for insertion of the sample into the O2k-chamber and for handling in combination with Forceps\stainless Steel\rounded Tip\sharp.
GainThe gain is an amplification factor applied to an input signal to increase the output signal.
High signal at zero oxygenA high signal at zero oxygen may be observed during zero calibration (R0). First, check the quality of the dithionite solution. The following instructions show how to distinguish between a defective sensor head and an electrical leak current.
High-resolution respirometryHRR
O2k-FluoRespirometer
High-resolution respirometry, HRR, is the state-of-the-art approach in mitochondria and cell research to measure respiration in various types of mitochondrial preparations and living cells combined with MultiSensor modules.

Mitochondrial function and dysfunction have gained increasing interest, reflecting growing awareness of the fact that mitochondria play a pivotal role in human health and disease. HRR combines instrumental accuracy and reliability with the versatility of applicable protocols, allowing practically unlimited addition and combination of substrates, inhibitors, and uncouplers using the Oroboros O2k-technology. Substrate-uncoupler-inhibitor titration (SUIT) protocols allow the interrogation of numerous mitochondrial pathway and coupling states in a single respirometric assay. Mitochondrial respiratory pathways may be analyzed in detail to evaluate even minor alterations in respiratory coupling and pathway control patterns.

The O2k-technology provides sole source instruments, with no other available instrument meeting its specifications for high-resolution respirometry. Technologically, HRR is based on the Oroboros O2k-technology, combining optimized chamber design, application of oxygen-tight materials, electrochemical sensors, Peltier-temperature control, and specially developed software features (DatLab) to obtain the unique sensitive and quantitative resolution of oxygen concentration and oxygen flux, with both, a closed-chamber or open-chamber mode of operation (TIP2k). Standardized calibration of the polarographic oxygen sensor (static sensor calibration), calibration of the sensor response time (dynamic sensor calibration), and evaluation of instrumental background oxygen flux (systemic flux compensation) provide the experimental basis for high accuracy of quantitative results and quality control in HRR. HRR can be extended for MultiSensor analysis by using the O2k-Fluo Smart-Module. Smart Fluo-Sensors are integrated into the O2k to measure simultaneously fluorometric signals using specific fluorophores. Potentiometric modules are available with ion-selective electrodes (pH, TPP+). The PB-Module extends HRR to PhotoBiology with accurate control of the light intensity and measurement of photosynthesis. The O2k and the NextGen-O2k support all these O2k-Modules. The NextGen-O2k all-in-one, however, is unique in supporting Q-Redox and NADH-Redox Modules.
Hydrogenion fluxJH+Volume-specific hydrogenion flux or H+ flux is measured in a closed system as the time derivative of H+ concentration, expressed in units [pmol·s-1·mL-1]. H+ flux can be measured in an open system at steady state, when any acidification of the medium is compensated by external supply of an equivalent amount of base. The extracellular acidification rate (ECAR) is the change of pH in the incubation medium over time, which is zero at steady state. Volume-specific H+ flux is comparable to volume-specific oxygen flux [pmol·s-1·mL-1], which is the (negative) time derivative of oxygen concentration measured in a closed system, corrected for instrumental and chemical background. pH is the negative logarithm of hydrogen ion activity. Therefore, ECAR is of interest in relation to acidification issues in the incubation buffer or culture medium. The physiologically relevant metabolic H+ flux, however, must not be confused with ECAR.
ISE Package 1 TPP or Ca
ISE Package 1 TPP or Ca.JPG
O2k-TPP+ and Ca2+ ISE\1 Chamber: ISE-Package for 1 TPP+ and Ca2+ electrode.
ISE-Ca2+ Membranes
Ca2+ membranes.jpg
ISE-Ca2+ Membranes: PVC, 4 mm diameter, box of 5 membranes. To be used with the O2k-TPP+ ISE-Module.
ISE-Compressible Tube
ISE-Compressible Tube.JPG
ISE-Compressible Tube for Ion-Selective Electrode TPP+ and Ca2+.
ISE-Filling Syringe
ISE-Filling Syringe.JPG
ISE-Filling Syringe with needle for Ion-Selective Electrode TPP+ and Ca2+.
ISE-Inner Glass Electrode
ISE-Inner Glass Electrode.JPG
ISE-Inner Glass Electrode of ISE, with Ag/AgCl- and Pt-wire
ISE-Membrane Mounting Tool
ISA-Membrane Mounting Tool.JPG
ISE-Membrane Mounting Tool for Ion-Selective Electrode TPP+ and Ca2+. O2k-TPP+ ISE-Module: mounting tool included.
ISE-Membrane Seal
ISE-Membrane Seal.JPG
ISE-Membrane Seal for Ion-Selective Electrode TPP+ and Ca2+.
ISE-TPP+ Membranes
ISE-TPP+ Membranes.JPG
ISE-TPP+ Membranes, PVC, 4 mm diameter, box of 5 membranes.
ISS-Filter and Tubing
ISS-Filter and Tubing.JPG
ISS-Filter and Tubing, ISS-Integrated Suction System.
ISS-Lid
ISS-Lid.JPG
ISS-Lid, for ISS-Waste Bottle, component of the ISS-Integrated Suction System.
ISS-Waste Bottle
ISS-Waste Bottle.JPG
ISS-Waste Bottle, 2-liter, component of the ISS-Integrated Suction System.
Inside the O2kA glance inside the Oroboros O2k
Ion-Selective Electrode TPP+ and Ca2+
Ion-Selective Electrode TPP+ and Ca2+.JPG
Ion-Selective Electrode TPP+ and Ca2+: ISE with 6 mm outer diameter shaft, for Stopper\white PVDF\angular Shaft\side+6.2+2.6 mm Port. O2k-TPP+ ISE-Module: 2 ISE.
Light-emitting diodeLEDA light-emitting diode (LED) is a light source (semiconductor), used in many every-day applications and specifically in fluorometry. LEDs are available for specific spectral ranges across wavelengths in the visible, ultraviolet, and infrared range.
Microbalance-Transport Case
Microbalance-Transport Case.jpg
Microbalance transport case, not suitable for shipping
Microsyringe\10 mm3 51/0.13 mm
Hamilton Syringes for Manual Titration.jpg
Hamilton Microsyringe\10 mm3 51/0.13 mm for manual titrations, 10 mm3 volume; fixed injection needle with rounded tip: 51 mm length, 0.13 mm inner diameter.
Microsyringe\100 mm3 51/0.41 mm
Microsyringe 100 mm3 51 0.41 mm - Kopie.JPG
Hamilton Microsyringe\100 mm3 51/0.41 mm for manual titrations, 100 mm3 volume; fixed needle with rounded tip: 51 mm length, 0.41 mm inner diameter. It is recommended for injections of suspensions of isolated mitochondria.
Microsyringe\200 mm3\TIP2k
Microsyringe200 mm3TIP2k.JPG
Microsyringe\200 mm3\TIP2k: Microinjection syringe for Titration-Injection microPump, 200 mm3 (µl), fixed injection needle with rounded tip, with spacers.
Microsyringe\25 mm3 51/0.15 mm
Microsyringe 25 mm3 51 0.15 mm.JPG
Hamilton Microsyringe\25 mm3 51/0.15 mm for manual titrations, 25 mm3 volume; fixed needle with rounded tip: 51 mm length, 0.15 mm inner diameter.
Microsyringe\50 mm3 51/0.15 mm
Microsyringe 100 mm3 51 0.41 mm - Kopie.JPG
Hamilton Microsyringe\50 mm3 51/0.15 mm for manual titrations, 50 mm3 volume; fixed needle with rounded tip: 51 mm length, 0.15 mm inner diameter.
Microsyringe\500 mm3\TIP2k
Microsyringe 500 mm3 TIP2k.JPG
Microsyringe\500 mm3\TIP2k: Microinjection syringe for Titration-Injection microPump, 500 mm3 (µl), fixed injection needle with rounded tip, with spacers.
MultiSensor-Connector
30420-24 MultiSensorConnector.JPG
MultiSensor-Connector: for separate reference electrode and ISE; only for O2k-Series B and Series C with MultiSensor electronic upgrading before 2011.
MultiSensor-Preamplifier 1/100
30430--24 NO-Attachment.JPG
MultiSensor-Preamplifier 1/100: Required only for O2k-Series A-C, for application of NO (or other amperometric) sensors (single chamber mode of application).
NADH-Module
NADH-Module - 12700-01.jpg
The NADH-Module, is a component of the NextGen-O2k for simultaneous measurement of oxygen consumption and NAD(P)H autofluorescence. NAD(P)H autofluorescence is used to evaluate the redox state of the NAD(P)H-pool. The NADH-Module incorporates an UV light and NADH-Sensors which include a photodiode and specific filters.
NADH-Sensor
NADH sesnor 003.png
The NADH-Sensor has been developed as a part of the NADH-Module for simultaneous monitoring of oxygen consumption and NADH redox state. The NADH-Sensor is composed of a photodiode and equipped with three supergel R370 Italian blue filters (Rosco, US).
O-ring sV\Viton\9.5x1 mm
34310-02.jpg
O-ring sV\Viton\9.5x1 mm, for PEEK Stopper sV, 2 are mounted on each PEEK Stopper sV, box of 8 as spares.
O-ring\Viton\12.5x1 mm
O-ringViton12.5x1 mm.jpg
O-ring\Viton\12.5x1 mm, for PVDF or PEEK O2k-Stoppers (2-mL O2k-Chamber), box of 8 as spares.
O-ring\Viton\16x2 mmO-ring\Viton\16x2 mm, mounted on the O2k-Chamber Holder sV.
O-ring\Viton\18x2 mm
Viton O-ring 18x2.jpg
O-ring\Viton\18x2 mm, mounted on the O2k-Chamber Holder.
O-ring\Viton\6x1 mm
POS O-ring for sensor head or POS mounting tool.jpg
O-ring\Viton\6x1 mm for POS-Mounting Tool.
O-ring\Viton\8x1 mm
POS O-ring for sensor head or POS mounting tool.jpg
O-ring\Viton\8x1 mm: for OroboPOS sensor head. Replaces the O-ring\Viton\9x1 mm
O2-Zero Powder
O2-Zero Powder.jpg
O2-Zero Powder, dithionite (Na2S2O4), for zero-oxygen calibration of the OroboPOS.
O2kO2kO2k - Oroboros O2k: the modular system for high-resolution respirometry.
O2k repairO2k repair of defective hardware may require replacement of spare parts. Some electronic or mechanical defects may be solved only by repair of the O2k in the electronics workshop of Oroboros Instruments, e.g., a defective Peltier unit (temperature control).
O2k series
The serial number of each O2k is shown on a sticker at the rear of the O2k.
The O2k series is specified as the capital letter in the O2k serial number of the Oroboros O2k. A serial number G-#### or H-#### denotes an Oxygraph from the G or H series, while XA-### denotes a NextGen-O2k from the A series. With DatLab running real-time connected to the O2k, the serial number of the currently connected O2k is displayed: (1) in the right corner of the status line, besides the DatLab version number (bottom), and (2) in windows O2k control [F7] and O2k configuration.
O2k signals and outputThree electronic channel types are available in the O2k-MultiSensor system. All channels are available twofold (dual-data), for O2k-Chambers A (left) and B (right), based on numerical signals sent at a fixed data sampling time interval (default: 2 s; range 0.2 s to >10 s).
O2k-Amperometric OroboPOS Twin-ChannelO2k-Amperometric OroboPOS Twin-Channel: Two-channel variable polarization voltage; current/voltage converter for the polarographic oxygen sensor (POS); amplifyer with digital gain settings (1x, 2x, 4x, 8x); A/D converter; output in the range -10 V to 10 V. Integral component of the O2k-Main Unit.
O2k-Assembly KitThe O2k-Assembly Kit is a component of the Oroboros O2k, consisting of 2 PVDF Stirrer-Bars, 2 PEEK O2k-Stoppers, OroboPOS-Connectors for O2k-series A-I and NextGen-O2k series XA (attached to the O2k-Main Unit) and cables (power supply, USB-connection). Several components of the O2k-Assembly Kit are included in the O2k-Accessory Box either for shipment or for storage.
O2k-Barometric Pressure TransducerO2k-Barometric Pressure Transducer, A/D converter and digital output to DatLab for continuous recording of barometric pressure [kPa or mmHg], integrated into the air calibration of the POS (MiPNet06.03 POS-calibration-SOP). Integral component of the O2k-Main Unit. The warranty on the accuracy of the signal obtained from the O2k-Barometric Pressure Transducer expires within three years.
O2k-Chamber Holder
Chamber holder PVDF Stopper.jpg
O2k-Chamber Holder (blue POM) for PVDF or PEEK stoppers (2-mL O2k-chamber), with O-ring\Viton\18x2 mm and V-ring\30-35-4.5 mm. Two units of this item are standard components mounted on the O2k-Main Unit.
O2k-Chamber Holder sV
32100-01.jpg
O2k-Chamber Holder sV (black POM) for PVDF or PEEK stoppers (0.5-mL O2k-chamber), with O-ring\Viton\16x2 mm and V-ring\30-35-4.5 mm.
O2k-Chamber sV
33100-01.jpg
O2k-Chamber sV: 12 mm inner diameter, Duran® glass polished, with standard operation volume V of 0.5 mL.
O2k-Electromagnetic Stirrer Twin-ControlO2k-Electromagnetic Stirrer Twin-Control for smooth rotation of the stirrer bars in the two O2k-chambers; with slow-start function to prevent decoupling of the stirrer bar; regulated stirrer speed in the range of 100 to 800 rpm (decoupling may occur at higher stirrer speeds), independent for the two O2k-Chambers; automatic events sent to DatLab when the stirrer is switched on/off or when the rotation seed is changed by the experimenter. Integral component of the O2k-Main Unit.
O2k-Fluo LED2-Module
Fluorescence-Control Unit lettered.jpg
The O2k-Fluo LED2-Module is a component of the O2k-Fluorometer (O2k-Series D to G). It is an amperometric add-on module to the O2k-Core (O2k-Series D to G), adding a new dimension to high-resolution respirometry. Optical sensors are inserted through the front window of the O2k-glass chambers, for measurement of hydrogen peroxide production (Amplex® UltraRed), ATP production (Magnesium Green™), mt-membrane potential (Safranin, TMRM, Rhodamine 123), Ca2+ (Calcium Green™), and numerous other applications open for O2k-user innovation.
O2k-Fluo Smart-ModuleThe O2k-Fluo Smart-Module is an amperometric add-on module to the O2k-Respirometer, adding a new dimension to high-resolution respirometry. Optical sensors are inserted through the front window of the O2k-glass chambers, for measurement of hydrogen peroxide production (Amplex® UltraRed), ATP production (Magnesium Green™), mt-membrane potential (Safranin, TMRM), Ca2+ (Calcium Green™), and numerous other applications open for O2k-user innovation.
» MiPNet28.09 O2k-Fluo Smart-Module manual
O2k-FluoRespirometer
O2k-FluoRespirometer
The Oroboros O2k-FluoRespirometer - the experimental system complete for high-resolution respirometry (HRR), including fluorometry, the TIP2k and the O2k-sV-Module allowing simultaneous monitoring of oxygen consumption together with either ROS production (AmR), mt-membrane potential (TMRM, Safranin and Rhodamine 123), Ca2+ (CaG) or ATP production (MgG). The O2k-FluoRespirometer supports all add-on O2k-Modules: O2k-TPP+ ISE-Module, O2k-pH ISE-Module, O2k-NO Amp-Module, enabling measurement of mt-membrane potential with ion sensitive electrodes (ISE for TPP+ or TPMP+) or pH.
O2k-Fuse Power Plug\M2.5 A\5x20 mm
Fuses mains.jpg
O2k-Fuse Power Plug\M2.5 A\5x20 mm: This item is a standard component of the O2k-Assembly Kit (O2k-FluoRespirometer), mounted on the socket for the O2k-Main Power Cable, at the rear panel of the O2k-Main Unit.
O2k-Main Power CableO2k-Main Power Cable, for connecting the main unit to the power supply.
O2k-Main Power Cable\120 V\US-CA
O2k-Main Power Cable 120 V US-CA.JPG
O2k-Main Power Cable\120 V\US-CA, USA and Canada (120 V).
O2k-Main Power Cable\230 V\AU-NZ
O2k-Main Power Cable 230 V AU-NZ.JPG
O2k-Main Power Cable\AU-NZ, Australia and New Zealand (230 V).
O2k-Main Power Cable\230 V\Europe
O2k-Main Power Cable 230 V Europe.JPG
O2k-Main Power Cable\230 V\Europe.
O2k-Main UnitThe O2k-Main Unit is a component of the O2k or the NextGen-O2k (more information). The O2k-Main Unit consists of functionally defined, integral elements, the (O2k-Main Basic, O2k-Peltier Temperature Control, two O2k-Electromagnetic Stirrer Twin-Control units, two O2k-Amperometric OroboPOS Twin-Channels, O2k-Barometric Pressure Transducer), which cannot be obtained separately.
O2k-NO Amp-Module
O2k-NO Amp-Module.jpg
O2k-NO Amp-Module: NO-sensor compatability pack an amperometric add-on for O2k-MultiSensor application The NO sensor is not included.
O2k-Peltier Temperature ControlO2k-Peltier Temperature Control: Built-in electronic thermostat controlling temperature for two O2k-chambers in the range of 4 to 47 °C; ±0.002 °C (at room temperature). Continuous recording of the O2k-Copper Block temperature with DatLab. Temperature change from 20 to 30 °C within 15 min; cooling from 30 to 20 °C within 20 min. Integral component of the O2k-Main Unit. The electronic temperature control of the O2k replaced the conventional water jacket.
O2k-Specifications
O2k-Info.png
O2k versus multiwell respirometer: O2k stands for Oroboros O2k and high-resolution respirometry, meeting powerful quality criteria securing high output and pioneering state-of-the-art comprehensive OXPHOS analysis of substrate control and coupling control of mitochondrial function. 'High throughput' stands for disposable multiwell systems - expensive, with limited scope and extremely high running costs. In respirometry, high throughput is not equivalent to high output. If you’re using a biased instrument, it doesn’t matter how many measurements you take – you’re aiming at the wrong target (Silver 2012 Penguin Press).
O2k-TPP+ ISE-Module
TPP new.jpg
O2k-TPP+ ISE-Module: Potentiometric ion-selective electrodes for measurement of mitochondrial membrane potential
O2k-USB Flash Drive
Oroboros-USB-flash-drive.JPG
The O2k-USB Flash Drive is a component of the Oroboros O2k containing: DatLab, O2k-Manual, O2k-Protocols, O2k-Publications, and info on O2k-Workshops.
O2k-Window Frame
O2k-Window Frame.JPG
O2k-Window Frame: blue POM, with thread for fixation on the O2k-Main Unit, to be removed only for rare cleaning purposes and for front fixation of the Fluorescence-Control Unit, using the O2k-Window Tool.
O2k-chamber
O2k-Chamber.jpg
O2k-Chamber: Duran® glass polished, with standard operation volumes (V) of 2.0 mL (O2k-nV, nominal volume, 16 mm inner diameter) or 0.5 mL (O2k-sV, small volume in the O2k-sV-Module, 12 mm inner diameter). The optical properties of Duran® allow application of fluorometric sensors (Duran® optical properties).
O2k-pH ISE-Module
PH new.jpg
O2k-pH ISE-Module: two pH electrodes and reference electrodes and accessories
O2k-sV-ModuleO2k-sV-Module
11200-01.jpg
The O2k-sV-Module is the O2k small-volume module, comprised of two Duran® glass chambers of 12 mm inner diameter specifically developed to perform high-resolution respirometry with reduced amounts of biological sample, and all the components necessary for a smaller operation volume V of 0.5 mL. The current DatLab version is included in the delivery of this revolutionary module.
OroboPOS
OroboPOS.JPG

The OroboPOS is a polarographic oxygen sensor (POS), with an amperometric mode of operation. The OroboPOS meets the highest quality criteria in terms of linearity, stability and sensitivity of the signal. The Clark type polarographic oxygen sensor (POS) remains the gold standard for measuring dissolved oxygen in biomedical, environmental and industrial applications over a wide dynamic oxygen range.

It consists of a gold cathode, a silver/silverchloride anode and a KCl electrolyte reservoir separated from the sample by a 25 µm membrane (FEP). The main body of the OroboPOS is made of PEEK. With application of a polarization voltage (0.8 V), a current is obtained as an amperometric signal, which is converted to a voltage.
OroboPOS-Connector
POS connector and cable connection.jpg
OroboPOS-Connector (blue POM), with male connection to OroboPOS head (POS) and with cable and male plug fitting into O2k-Main Unit.
OroboPOS-Connector ServiceThe OroboPOS-Connector Service entails routine maintenance and any necessary repairs of the OroboPOS-Connector in the Oroboros electronics workshop (WGT).
Oroboros O2k-technology
NextGen-O2k all-in-one

The Oroboros O2k-technology provides modular systems for high-resolution respirometry (HRR) for mitochondria and cell research. Oroboros delivers the O2k-technology for high-resolution respirometry in mitochondria and cell research. The O2k-tecnology allows the measurement of respiration at controlled oxygen levels, combined with redox biology (NADH and CoQ), ROS production, mitochondrial membrane potential, ATP production, Ca2+, or pH. HRR expands to HRPB: High-Resolution PhotoBiology.

Small amounts of biological samples can be used for bioenergetic and OXPHOS analysis, ranging from isolated mitochondria, permeabilized tissues and permeabilized cells to living cells and tissues slices.

The modular O2k-concept is supported by DatLab, with high flexibility for extension by add-on O2k-Modules. All O2k-Modules are supported by the NextGen-O2k. The O2k-Q-Module and the O2k-NADH-Module are exclusively supported by the NextGen-O2k, whereas the O2k (Series-J) provides the basis for all other HRR application but cannot be upgraded to the NextGen-O2k Redox. The globally tested and trusted high-resolution O2k-technology prioritizes both quality and scientific research output in the field of mitochondrial physiology and pathology, extended to PhotoBiology.
Oxygen sensor testPOS testThe O2 sensor test is an important component of Oroboros Quality Management. The OroboPOS test is described in detail in MiPNet06.03 POS-calibration-SOP, is performed after switching on the Oroboros O2k, and is required as a basis of technical service of the instrument.
PB Light Source
PB-Sensor.png
The PhotoBiology Light Source (PBLS) has been designed as a part of the PB-Module to provide with an external source of light. This enables experiments for evaluating the production of O2 in the presence of light. The PBLS consists of one LED and one photodiode mounted on the PBLS head protected by a PMMA plastic cover. Three pairs of PBLS (white, blue, and red) are provided with the PB-Module. The light intensity can be regulated from 0 to 2750 µmol·s-1·m-2 (red PBLS), from 0 to 3000 µmol·s-1·m-2 (blue PBLS), from 0 to 3500 µmol·s-1·m-2 (white PBLS). An integrated photodiode provides real-time measurement of the light intensity allowing for continuous adjustment to the desired value.
PB-Module
PB-Module.jpg
The PB-Module has been developed for conducting measurements of PhotoBiology, including photosynthesis. It consists of the PB Light Source and electronic components which are an integral part of the NextGen-O2k. Measurements are recorded and evaluated with the DatLab 8 software.
PBI-Shredder SG3
PBI-Shredder SG3.jpg
PBI-Shredder SG3 for tissue homogenate preparation, heavy duty high torque SG3 driver with convertible handle, SG3 base with 3 position force setting lever (FSL), battery charger and two lithium ion batteries. The PBI-Shredder SG3 is included in the PBI-Shredder O2k-Set. Select 230 V or 120 V. Oroboros Instruments: world-wide distributor.
PC requirementsThe PC requirements for controlling an O2k and data recording with DatLab are found here.
PH-Glass electrode
PH-Glass Electrode.JPG
pH-Glass electrode with BNC plug.
POS-Electrolyte Powder
POS Electrolyte powder.jpg
POS-Electrolyte Powder, KCl. The powder is dissolved in 10 ml distilled water to yield a 1 M KCl solution.
POS-Holder
Pos holder.JPG
The POS-Holder, made from blue POM, is screwed into the copper block of the O2k-Main Unit, guiding theguiding the POS to the 2-mL O2k-chamber, and keeping the SmartPOS/OroboPOS-Connector in a fixed position for sealing the O2k-chamber with the POS-Seal Tip. In addition, the POS-Holder fixes the O2k-Chamber in an accurate rotational position by pressing against the angular cut of the glass chamber. Two units of this item are standard components mounted on the O2k-Main Unit.
POS-Holder sV
32300-01.jpg
POS-Holder sV, made from black POM, to be screwed into the copper block of the O2k-Main Unit, guiding the POS to the O2k-Chamber sV, and keeping the SmartPOS/OroboPOS-Connector in a fixed position for sealing the O2k-Chamber sV with the POS-Seal Tip. In addition, the POS-Holder sV fixes the O2k-Chamber sV in an accurate rotational position by pressing against the angular cut of the glass chamber.
POS-Membrane Ring
POS membrane holder ring.jpg
POS-Membrane Ring, PEEK, holds the membrane against the inner O-ring on the POS housing.
POS-MembranesFEP-membranes
POS membranes.jpg
POS-Membranes, FEP 25 µm; 40/Pck.
POS-Mounting Tool
POS mounting tool for membrane application 02.JPG
POS-Mounting Tool for application of POS-Membranes. It consists of two parts, (i) the membrane guide (larger diameter) and (ii) the membrane ring holder with O-ring\Viton\6x1 mm for holding the POS-Membrane Ring during membrane application. Since the O2k-Series G-0075 membrane ring holder have a 2 mm extended ridge for a better grip.
POS-Seal Tip
POS seal tip.jpg
POS-Seal Tip, black butyl rubber gasket with 3 mm pore. 4/Pck, for sealing the POS (sensor head) against the O2k-Chamber. Push the wetted POS-Seal Tip over the POS-sensor head, with the pore positioned centrally, not covering any peripheral area of the gold cathode. Do not stretch the gasket across the POS-sensor head.
Pipette\Plastic\1 ml ungraded
Pipette Plastic 1 ml-ungraded.JPG
Pipette\Plastic\1 mL ungraded, for filling electrolyte into the reservoir of the OroboPOS.
Plunger\10 mm3
Plunger 10 mm3.JPG
Plunger\10 mm3 for Microsyringe\10 mm3 51/0.13 mm, spare.
Polarization voltageUA polarization voltage of 600 mV to 800 mV is applied between anode and cathode of the polarographic oxygen sensor, resulting in a current when oxygen is consumed. The current is converted by the electronics to a voltage (raw signal) which must not be confused with the polarization voltage.
Polarographic oxygen sensorPOSPolarographic oxygen sensors (POS) are operated with a polarization voltage between the cathode and anode, connected by an electrolyte. Cathode, anode and electrolyte are separated from the analyte by an oxygen-permeable membrane. Oxygen is reduced at the cathode such that the local oxygen concentration is maintained at zero, and diffuses along the concentration gradient from the stirred medium to the cathode, resulting in a linear calibration between oxygen partial pressure and electric current [Amp] (amperometric mode of operation). The OroboPOS is the POS applied in the Oroboros O2k.
Polishing Cloth
POS polishing cloth for cathode cleaning.jpg
Polishing Cloth for cathode cleaning. Replace the Polishing Cloth at intervals. A two-year interval may be considered in cases of intensive use.
Polishing Powder
POS polishing powder for cathode cleaning.jpg
Polishing Powder 0.3 µm and Polishing Powder 0.05 µm for cathode cleaning of OroboPOS and Q-sensors.
PotentiometryPotentiometry is the general term given to the method of measuring the electric potential difference between two electrodes connected by an electrolytic solution. The potential of the reference electrode is constant. The other electrode is called the indicator electrode. If this is an ion-selective electrode which is in equilibrium with the solution, the measured electric potential difference is proportional to the (negative) logarithm of the activity of a specific ion in the solution. Examples are the pH glass electrode for measurement of pH, and the TPP+ electrode for measurement of pTPP and calculation of mt-membrane potential.
Power O2k Numbers
Power O2k Numbers.JPG
Power O2k Numbers: Single number to label the O2k in a Power O2k-Lab.
Power O2k-FluoRespirometer
Power O2k-FluoRespirometer
Power O2k-FluoRespirometer - optional configuration as additional system for increasing output combined with the O2k-FluoRespirometer (O2k-Series H). The Power O2k-FluoRespirometer includes the TIP2k and the O2k-sV-Module, and supports all add-on O2k-Modules of the Oroboros O2k. It can be added to an existing Oroboros O2k of any O2k-Series. This application does not require an additional ISS-Integrated Suction System and O2k-Titration Set. Furthermore, the OroboPOS-Mounting Tool of the OroboPOS Service Tools can be used from the available O2k and is not included.
Power O2k-Respirometer
Power O2k notext.png
The Power O2k-Respirometer is an economical option for using additional O2k-Units to increase output in high-resolution respirometry.
Q-ModuleQ-Module
Q-box 002.jpg
The Q-Module, developed for measuring the Q redox state and cyclic voltammetry, is supported by the NextGen-O2k and consists of the Q-Sensor, integrated electronic components in the O2k, and the DatLab software.
Q-Sensor
Q stopper.jpg
The Q-Sensor has been designed as a part of the Q-Module for measurements with cyclic voltammetry and voltammetry, allowing for analysis of the Q redox state. The Q-Stopper with the reference electrode is called Q-Sensor, which is plugged in the NextGen-O2k. A three-electrode system is used to detect the Q redox state. Two of the three electrodes (glassy carbon and platinum electrode) are built into the Q-Stopper, while the reference electrode is removable (Reference-Electrode\2.4 mm).
Reference-Electrode\2.4 mm
Reference Electrode 2.4 mm.jpg
Reference-Electrode\2.4 mm: 2.4 mm diameter glass shaft, for ISE.
Replacement-Barrel
Replacement-Barrel.jpg
Replacement-Barrel for Reference-Electrode\2.4 mm, 2.4 mm diameter glass.
Scissors\stainless steel\straight Tip\sharp
Scissors stainless steel straight Tip sharp.jpg
Scissors\stainless steel\straight Tip\sharp.
Screwdriver allen wrench
24330-02.jpg
Screwdriver allen wrench, a standard component of the O2k-FluoRespirometer and O2k-sV-Module.
Search for defective O2k componentsThe 2-chamber design of the O2k helps to search for defective O2k components, by switching components linked to O2k chambers A and B between sides A and B.
Shipping an O2kFor shipping an O2k or parts, standard operating procedures have to be followed to avoid damage of the instrument and unexpected delays. The O2k-Main Unit must be shipped only in Packing\O2k-Box 1, without O2k-chambers and without OroboPOS. Two O2k-Chamber Holders, two OroboPOS-Holders and two OroboPOS-Connectors are attached to the O2k-Main Unit for transport.
Shredder-Tubes
Shredder-Tube Analyt Biochem.jpg
Shredder-Tubes: consisting of Shredder Tube FT500-PS with Lysis Disk, serrated Shredder-Tube Ram Tool and Shredder-Tube Cap Tool, coral colour (Box of 100) and Shredder Tube FT500-PMS with Lysis Disk, serrated Shredder-Tube Ram Tool and Shredder-Tube Cap Tool, coral colour (Box of 100). There is no difference between the white and the coral shredder tubes, except that the white tubes are also approved for high pressure.
Smart Fluo-Sensor Blue
SmartFluo.png
Smart Fluo-Sensor Blue: Excitation LED 465 nm (dominant wavelenght) with short pass filter, emission (red) with long pass filter, individual sensors are calibrated with sensor-specific memory and direct input into DatLab 7 to obtain reproducible light intensities with different sensors, including photodiode, Filter-Cap equipped with Filter Set Saf for measurement of mitochondrial membrane potential with safranin and rhodamine 123. Filter Set MgG / CaG for Magnesium green and Calcium green measurements are included.
Smart Fluo-Sensor Green
SmartFluo.png
Smart Fluo-Sensor Green: Excitation LED 525 nm (dominant wavelength) with short pass filter, emission (red) with long pass filter, individual sensors are calibrated with sensor-specific memory and direct input into DatLab 7 to obtain reproducible light intensities with different sensors, including photodiode, Filter-Cap equipped with Filter Set AmR for Amplex UltraRed and TMRM measurements when delivered.
SmartPOS
DSC 0491 SmartPOS.jpg

The SmartPOS is a polarographic oxygen sensor (POS), for O2k-Series J and XB onward, with an amperometric mode of operation. The SmartPOS combines the previous OroboPOS and OroboPOS-Connector and is automatically recognized by the software DatLab 8. Combination of the previously separated components in one piece, protects the electrical connections. The SmartPOS is, like the OroboPOS, a Clark type polarographic oxygen sensor (POS), which remains the gold standard for measuring dissolved oxygen in biomedical, environmental and industrial applications over a wide dynamic oxygen range. The SmartPOS meets the highest quality criteria in terms of linearity, stability and sensitivity of the signal.

The sensor consists of a gold cathode, a silver/silverchloride anode and a KCl electrolyte reservoir separated from the sample by a 25 µm membrane (FEP). With application of a polarization voltage (0.8 V), a current is obtained as an amperometric signal.
Startup O2k-Respirometer
Startup O2k-Respirometer notitle.png
Startup O2k-Respirometer - the experimental system complete for basic high-resolution respirometry (HRR). The O2k-Respirometer includes the O2k-Main Unit with stainless steel housing, O2k-Assembly Kit, two OroboPOS (polarographic oxygen sensors) and OroboPOS-Service Kit, DatLab software, the ISS-Integrated Suction System, the O2k-Titration Set, and for performing high-resolution respirometry with reduced amounts of biological sample the O2k-sV-Module.


The O2k is a sole source apparatus with no other instruments meeting its specifications.
Stirrer-Bar sV\white PVDF\11.5x6.2 mm
33210-01.jpg
Stirrer-Bar sV\white PVDF\11.5x6.2 mm, operated in the 0.5-mL O2k-Chamber sV at constant stirring speed (standard is 750 rpm, or 12.5 Hz), to provide optimum mixing of the sample in the aqueous medium and ensure a stable signal of the polarographic oxygen sensor (OroboPOS) placed in a position of maximum current of the medium.
Stirrer-Bar\black PEEK\15x6 mm
Stirrer-Bar black PEEK15x6 mm.JPG
Stirrer-Bar\black PEEK\15x6 mm, for 2-mL O2k-Chamber, for specific optical applications to minimize optical interference.
Stirrer-Bar\white PVDF\15x6 mm
Stirrer bar PVDF.jpg
Stirrer-Bar\white PVDF\15x6 mm, operated in the 2-mL O2k-chamber at constant stirring speed (standard is 750 rpm, or 12.5 Hz), to provide optimum mixing of the sample in the aqueous medium and ensure a stable signal of the polarographic oxygen sensor (OroboPOS) placed in a position of maximum current of the medium.
Stopper sV\black PEEK\conical Shaft\central Port
34000-01.jpg
Stopper sV\black PEEK\conical Shaft\central Port: with conical shaft (with PTFE, graphite, carbon fiber) and one central capillary (1.0 mm diameter; 48.9 mm length), Volume-Calibration Ring sV (A or B) for volume adjustment 0.5 mL; 2 mounted O-rings (O-ring sV\Viton\9.5x1 mm).
Stopper-Needle
Stopper-Needle.JPG
Stopper-Needle: Short needle for bubble extrusion from port of the ISE-stopper.
Stopper-Spacer
Gas spacer for Stopper.jpg
Stopper-Spacer (or gas spacer) to set the O2k-Stopper into a standard position for a fixed gas phase above the aqueous phase in the 2-mL O2k-chamber, during air calibration or for injection of nitrogen, argon or oxygen into the gas phase; Stopper-Spacer thickness of 4mm (a deviation of +/- 10% possible).
Stopper\black PEEK\angular Shaft\side+6.2+2.6 mm Port
Stopper black PEEK angular Shaft side+6.2+2.6 mm Port.JPG
Stopper\black PEEK\angular Shaft\side+6.2+2.6 mm Port, for application with ISE; side titration port and two additional holes (6.2 mm and 2.6 mm); angular bottom; including Volume-Calibration Ring (A or B); 2 mounted O-rings, with 8 spare O-rings (O-ring\Viton\12.5x1 mm).
Stopper\black PEEK\conical Shaft\central Port
Stopper black PEEK conical Shaft central Port.JPG
Stopper\black PEEK\conical Shaft\central Port: with conical shaft (with PTFE, graphite, carbon fiber) and one central capillary (1.3 mm diameter; 50.6 mm length), Volume-Calibration Ring (A or B) for volume adjustment 1.5 to 3.2 ml; 2 mounted O-rings, with 8 spare O-rings (O-ring\Viton\12.5x1 mm). The black PEEK stoppers are required for optical O2k-MultiSensor Modules.
Stopper\black PEEK\conical Shaft\central Port\peripheral 2.3 mm Port
Stopper black PEEK conical Shaft central Port peripheral 2.3 mm Port.JPG
Stopper\black PEEK\conical Shaft\central+peripheral 2.3 mm Port: for potentiometric O2k-MultiSensor applications (NO, H2S, H2O2); 1 additional port (2.3 mm); central titration port; conical bottom; including Volume-Calibration Ring (A or B); 2 mounted O-rings, with 8 spare O-rings (O-ring\Viton\12.5x1 mm).
Stopper\black PEEK\conical Shaft\central+2.3+2.6 mm Port
Stopper black PEEK conical Shaft central+2.3+2.6 mm Port.JPG
Stopper\black PEEK\conical Shaft\central+2.3+2.6 mm Port: for pH and reference electrode, central titration port and two additional ports (2.3 mm and 2.6 mm); conical bottom; including Volume-Calibration Ring (A or B), 2 mounted O-rings, with 8 spare O-rings (O-ring\Viton\12.5x1 mm).
Syringe Collars
Syringe Collars.JPG
Syringe Collars (package of 20) for Hamilton microsyringes: for correctly storing the microsyringes in the Syringe Racks.
Syringe Labels
Syringe Labels 2017.JPG
Syringe Labels: set of labels with standard abbreviations (see O2k-Titrations).
Syringe Racks
Syringe Racks.JPG
Syringe Racks: stainless steel; for proper placement of eight Hamilton microsyringes in HRR experiments; package of two (for a total of 16 microsyringes).
Syringe Storage Box
Syringe Storage Box.jpg
Syringe Storage Box: for storing the Hamilton microsyringes; includes Syringe Labels.
Syringe\10 mL\Gas-Injection
Gas injection syringe.jpg
Syringe\10 mL\Gas-Injection, 10 mL, with spacer and stainless steel needle, flat tip, for gas injection into the O2k-chamber. 2 syringes are supplied with Oxia.
Syringe\500 mm3 51/0.41 mm
Syringe 500 mm3 51 0.41 mm.JPG
Hamilton Syringe\500 mm3 51/0.41 mm for manual titrations, 500 mm3 volume; fixed needle with rounded tip: 51 mm length, 0.41 mm inner diameter; for injections of suspensions of isolated mitochondria and filling of the Microsyringe\200 mm3\TIP2k.
Syringe\60 mL\Gas-Injection
Gas injection syringe.jpg
Syringe\60 mL\Gas-Injection, 60 mL, with spacer and stainless steel needle, flat tip, for gas injection into the O2k-chamber.
TIP2k Filter Papers
TIP2k Filter Papers.JPG
TIP2k Filter Papers (package of 10) to be used for the stoppers during TIP2k titration for Instrumental oxygen background correction to avoid constant manual siphoning off of extruded liquid.
TIP2k-Module
TIP2k with 200 mm3 microsyringe.JPG
TIP2k-Module - Titration-Injection microPump (TIP2k) for two-channel operation with the O2k-FluoRespirometer with automatic control by DatLab of programmable titration regimes and feedback control (oxystat, pH-stat).
TIP2k-Needle Safety Support with cable guide
31330-01 3.jpg
TIP2k-Needle Safety Support with cable guide: for safe storage of TIP2k-needles and MultiSensor Modules cables when not required during the experiment.
TIP2k-Needle Spacer
80600-24 Spacers f. TIP2k needle.JPG
TIP2k-Needle Spacers for microinjection TIP2k needle, silicone stops (200/Pkg.) with mounting tool.
Titration-Injection microPump
Titration-Injection-microPump.jpg
Titration-Injection microPump (TIP2k) for two-channel operation with the O2k with automatic control by DatLab of programmable titration regimes and feedback control (oxystat, pH-stat).
Tube Racks
Tube Racks.JPG
Tube Racks: stainless steel, accomodating four 50-ml tubes, for cleaning of microsyringes, cleaning and storage of stoppers during cleaning of the O2k-chambers; package of two (for a total of eight tubes).
USB-Cable 2.0\Type A-B
USB-Cable2.0 Type A-B.JPG
USB-Cable 2.0\Type A-B for connecting the O2k-Main Unit (O2k-Series E upwards) to the USB port of a PC or laptop.
Uninterrupted power supplyUPSA back-up power supply may be required to secure uninterrupted power supply.
V-ring\30-35-4.5 mm
V-Ring 30-35-4.5.JPG
V-ring\30-35-4.5 mm, mounted on O2k-Chamber Holder and O2k-Chamber Holder sV.
Vitonn.a.Viton® is a fluoroelastomer with excellent resistance to aggressive fuels and chemicals. Viton is resistant against oxygen diffusion which makes it an ideal material for high-resolution respirometry (Viton O-rings).
Volume-Calibration Ring
Volume calibration ring A+B PVDF for Stopper.jpg
Volume-Calibration Ring (A or B) PVDF for O2k-Stoppers (2-mL O2k-chamber), white; attached to the stoppers.
Volume-Calibration Ring sV
Volume calibration ring A+B PVDF for Stopper.jpg
Volume-Calibration Ring sV (A or B), white PVDF, attached to PEEK O2k-Stopper sV.
Cookies help us deliver our services. By using our services, you agree to our use of cookies.